Power / Generators • 7 min read • Updated 2026-11-20

Cummins Onan QG 4000 / 5500 Generator Code 36 & No-Start Diagnostic Playbook

Step-by-step campground troubleshooting for Onan QG generators that crank without starting or die after 3 seconds—covering 2nd-level blink retrieval, fuel cutoff, slip rings, and carb jets.

By CodeMyRV Technical Editorial Team — Verified against OEM service documentation.

Technical ParameterFactory Field Specification
Chassis Fuel Cutoff LevelStops Drawing Below 1/4 Tank (Built-In Safety)
Spark Plug Gap (167-0275)0.025 in. (0.64 mm)
Rotor Slip Ring Resistance20 – 28 Ohms (Voltage Reg Pins 9 & 10)
Oil Capacity (QG 4000 KY)1.6 Quarts (15W-40 / 10W-30 / 5W-30 Cold)
Oil Capacity (QG 5500/7000)2.0 Quarts (With Spin-On Filter 122-0836)
Monthly Exercise Schedule2 Hours/Month at >= 50% Load (1 Rooftop A/C)

How to Pull 2nd-Level Fault Codes on Any Onan QG Generator

Every Cummins Onan QG 4000 (KY), 5500, and 7000 generator communicates shutdown reasons through the amber status LED embedded in the START/STOP rocker switch. When an unexpected shutdown occurs, the amber light first displays a 1st-level fault (1, 2, 3, or 4 blinks). Nearly all field breakdowns show 3 blinks, which simply means 'Service Fault—dig deeper.'

To reveal the exact 2-digit 2nd-level code, wait until the amber light is actively blinking 3 times, then press and release the STOP side of the switch once. The light will immediately switch to a two-digit pattern: for example, 3 blinks, a brief pause, and 6 blinks equals Code 36. Pressing STOP again stops the blink readout, and the controller keeps the last fault stored in memory even if you walk away.

The 5-Minute Campground Check for Code 36 (Engine Stopped Without Command)

Code 36 is by far the most common RV generator fault in North America. Because the Onan control board only knows that the engine stopped spinning while ignition was still commanded, Code 36 covers fuel delivery, ignition spark, air restriction, and low oil shutdowns. Work through these four checks in exact order before buying tools or parts:

  1. Verify the RV Fuel Gauge Is Above 1/4 Tank: Motorhome chassis manufacturers cut the generator fuel pickup tube roughly three-quarters of the way down the main tank so you can never strand yourself running the A/C overnight. Even a 1/4-tank reading on a sloped campsite can uncover the pickup straw and starve the generator.
  2. Check Oil Level on Level Ground: The Onan low-oil float/pressure switch is notoriously sensitive. Being just 3 to 4 ounces below the FULL crosshatch—especially when parked nose-high—triggers an immediate Code 36 stall.
  3. Listen for the Electric Fuel Pump Prime: Press and hold the STOP/PRIME rocker switch for 5 seconds with the generator compartment door open. You should hear a distinct, rapid mechanical clicking from the 149-2311-02 electric fuel pump. Complete silence points to a seized pump, blown 5A fuse, or corroded pump ground.
  4. Pull the Spark Plug (167-0275): A wet, fuel-soaked plug indicates an ignition coil or fouled plug problem; a bone-dry plug after 10 seconds of cranking confirms fuel is never passing through the carburetor main jet.

Ethanol Varnish & Surging: Why QG 4000 Carburetors Fail

If your Onan QG 4000 fires briefly on a 1-second spritz of carburetor cleaner into the air intake throat and then dies, your ignition and oil switch are healthy—the fault is 100% fuel delivery. Standard E10 pump gasoline begins separating and leaving amber varnish inside tiny brass carburetor emulsion tubes in as little as 30 to 45 days of sitting idle.

Because the KY-series carburetor (OEM 146-0785) uses microscopic idle and main orifices beneath an altitude-adjustment cap, ultrasonic cleaning rarely lasts as reliably as installing a fresh OEM carburetor paired with a new inline fuel filter and fresh ethanol-free gasoline treated with marine fuel stabilizer. Running the generator for two full hours every month under a 50% load (such as one rooftop A/C) keeps fresh fuel moving through the bowl and evaporates moisture from the crankcase.

Diagnosing Code 27 & Code 13: Oxidized Slip Rings vs. Bad Voltage Regulator

When an Onan generator starts cleanly, runs smoothly for 3 to 5 seconds, and shuts down every single time with Code 27 (AC Voltage Sense Loss) or Code 13 (Undervoltage), the engine is usually fine—the electrical generation end is not producing clean AC output.

Disconnect the coach battery negative terminal, unplug the main harness at the 305-0982 voltage regulator, and measure resistance across Pins 9 and 10 (rotor brushes and copper slip rings). Factory specification sits cleanly between 20 and 28 Ohms. If your meter reads 45, 90, or 200+ Ohms, dark copper oxidation has coated the slip rings during storage. Cleaning the rings gently with a non-metallic Scotch-Brite pad restores resistance into spec and often cures Code 27 for free. If rotor resistance already reads 20–28 Ohms cleanly, the 305-0982 voltage regulator board itself has failed and should be replaced.

Technical Safety Reminder: Always disconnect 120V/240V AC shore power, switch off 12V battery disconnects, and close LP propane cylinder valves before removing electrical panels or testing gas burners. See our full Safety Disclaimer.

Jump Directly to Related Onan Generator Fault Codes

Referenced OEM Replacement Parts

Cummins Onan OEM: 149-2311-02
Onan QG 4000 Microlite Electric Fuel Pump
Cross-Ref: E11007 / 149-2311

Resolves Code 36 fuel starvation on KY-series 4000W gasoline generators.

Cummins Onan OEM: 146-0785
Onan QG 4000 Carburetor Assembly (KY Spec J-P)
Cross-Ref: 146-0803 / A041D736

Fixes surging, hunting, and Code 36 stalls from varnished jets.

Cummins Onan OEM: 305-0982
Onan QG Voltage Regulator Assembly
Cross-Ref: 305-0949

Fixes Code 13 (Undervoltage), Code 14 (Overfrequency), and Code 27 (Sense Loss).

Cummins Onan OEM: 167-0275
Onan QG 4000 / 5500 Spark Plug (Gap 0.025 in)
Cross-Ref: Champion RS17YX

Fouled plugs frequently trigger Code 36 or Code 45 cranking faults.

Frequently Asked Questions

Why does my Onan generator start only while I hold the START button, then die immediately?

When an Onan engine runs only while the starter button is held down and dies the instant you release it, the controller is not sensing AC voltage output from the generator end (commonly logging Code 27 or Code 36). Check rotor slip ring resistance (20-28 Ohms) and the 305-0982 voltage regulator.

What engine oil should I use in an Onan QG 4000 or 5500?

Cummins Onan recommends API SJ/CF or higher SAE 15W-40 for temperatures above 32°F, 10W-30 for moderate climates, and full-synthetic 5W-30 when camping below freezing to prevent Code 32 Low Cranking Speed shutdowns.

How do I reset an Onan generator fault code?

Onan fault codes automatically clear the next time the generator successfully starts and runs cleanly. To reset a latched lockout without starting, press STOP once or disconnect 12V battery power to the generator for 30 seconds.